Куда я попал?
SECURITM это SGRC система, ? автоматизирующая процессы в службах информационной безопасности. SECURITM помогает построить и управлять ИСПДн, КИИ, ГИС, СМИБ/СУИБ, банковскими системами защиты.
А еще SECURITM это место для обмена опытом и наработками для служб безопасности.

CVE-2026-99248

PUBLISHED 03.11.2026

CNA: Linux

i2c: xiic: restore non-managed runtime PM to fix clk WARN flood

Обновлено: 03.11.2026
In the Linux kernel, the following vulnerability has been resolved: i2c: xiic: restore non-managed runtime PM to fix clk WARN flood The devres conversion replaced manual pm_runtime_enable()/disable() with devm_pm_runtime_set_active_enabled() and dropped the remove-time runtime PM teardown. The managed release tears runtime PM down in the wrong order: it calls pm_runtime_dont_use_autosuspend() before pm_runtime_disable(), i.e. while runtime PM is still enabled, and devres is LIFO so the devm_clk_get_enabled() release runs afterwards. At remove(), pm_runtime_put_sync() leaves the device active with the autosuspend timer armed. Clearing use_autosuspend then makes rpm_idle() suspend immediately, and xiic_i2c_runtime_suspend() clk_disable()s the clock. The later devm_clk_get_enabled() release clk_disable_unprepare()s the already-disabled clock, so clk_core_disable() WARNs ("clkN already disabled") on every teardown. Drop the managed helper and restore the non-managed runtime PM setup and teardown, so runtime PM is enabled once in probe and disabled once in remove and the clock enable count stays balanced. Order the remove teardown so runtime PM is disabled before the usage count is dropped: pm_runtime_disable() followed by pm_runtime_put_noidle() instead of pm_runtime_put_sync(). Dropping the count first with autosuspend still enabled arms the autosuspend timer, and a preemption before pm_runtime_disable() lets it expire, suspend the device and clk_disable() the clock, which the devm release then disables again - the same WARN. Restore the non-managed IRQ request as well. The probe error paths now unwind runtime PM by hand via goto, and a devm-registered handler is only freed later during devres unwind, so it would stay live across the manual teardown (and across any future failing step added after it). Request the IRQ with request_threaded_irq() and free it explicitly in the probe error path and in remove. The probe error path also clears use_autosuspend, to match the teardown in remove().

Доп. Информация

Product Status

Linux
Product: Linux
Vendor: Linux
Default status: unaffected
Версии:
Затронутые версии Статус
Наблюдалось в версиях от 50c63491ff267f2860a6d8cb70c9a30ab701b9d3 до 47e105bdc863f2b320f9c05c80a63d3b83312700 affected
Наблюдалось в версиях от 50c63491ff267f2860a6d8cb70c9a30ab701b9d3 до d33373c565af9c8a28776af02bd20ba6e5724211 affected
Linux
Product: Linux
Vendor: Linux
Default status: affected
Версии:
Затронутые версии Статус
Наблюдалось в версии 7.1 affected
Наблюдалось в версиях от 0 до 7.1 unaffected
Наблюдалось до версии 7.2.* unaffected
Наблюдалось до версии * unaffected
 

Ссылки

Мы используем cookie-файлы, чтобы получить статистику, которая помогает нам улучшить сервис для вас с целью персонализации сервисов и предложений. Вы может прочитать подробнее о cookie-файлах или изменить настройки браузера. Продолжая пользоваться сайтом, вы даёте согласие на использование ваших cookie-файлов и соглашаетесь с Политикой обработки персональных данных.